Master Knitter Posts, Techniques, WiP Posts

Preparing to Steek

I promised my guild that I would videotape my cutting the steeks for my sweater, so I figured to be thorough I’d do a whole post on the process. 🙂  Stay tuned for the actual video – this post will walk you through leading up to the actual cutting.

Just FYI – this is a picture heavy post!

For those that don’t already know, a steek is a section of knitting that you are planning on cutting in your knitting.  You will use steeks when knitting things that are easier to knit in the round.  Fair Isle (and stranded) knitting is very often knit in the round (it doesn’t have to be, though!) – so steeks are commonly used in those types of knitting.  Why do you need to cut?  Well, if you want a cardigan you have to have an opening in the front.  You’ll need openings for the sleeves as well.  And if you want a v-neck or scoop neck, you’ll need a neckline opening, too.   These are all places you can use steeks.  You’ll essentially knit a large tube for the body of your sweater, and then cut it open for the front, and cut open the armholes and the neckline.

I don’t usually reinforce my steeks – they don’t typically need it if you’re using a ‘sticky’ wool, and if you make an intrinsically sturdy steek of about 8 or more stitches wide and a checkerboard pattern.  For this sweater, however, I used a very narrow steek of just 3 stitches on each side, and I used a stripe pattern.  The reason for this is because I’m going to use a ‘sandwich’ technique when I pick up the stitches for the buttonband and the collar.  (I’ll post about that when I get to that part of the sweater, too.)  This technique requires the steek to be very narrow, since the steek will end up hidden inside a row of knitting.  Because of this, I decided to reinforce all my steeks just to be extra sure they aren’t going anywhere. 🙂

Also, my steeks are all left with live stitches at the top, on holders – they need to be kept separate from the body of knitting, so I did not bind them off when the other stitches were bound off.

To reinforce, you need a small crochet hook and some yarn (I used the dark green color I’m going to be using on the buttonband.)  Place a slip knot on the crochet hook, and insert your hook directly above the cast on edge of the steek – two stitches in from the center of the steek.

DSC08299
Steek ready to be reinforced. (it’s upside down -the cast on edge is shown at top.)
DSC08300
Crochet hook inserted below cast on edge.
DSC08302
Slip stitch *over* the cast on edge to secure it.

I’m working on the left side of the steek here, so the hook goes in from the left to the center- under the right leg of the second stitch from the center, and the left leg of the stitch directly in from the center (I have 3 stitches on each side of the center in this steek.)

DSC08303
Crochet hook inserted into the two legs of the stitches to be secured.

Yarnover the hook, and pull through all three loops on the hook to make a slip stitch.

DSC08304
Yarnover the hook…
DSC08305
Pull through all three loops.

Repeat in this manner up the steek – getting every single row secured.

DSC08306
Next row…
DSC08308
And so on…

When you get to the top, the steek stitches are on a holder. Take the left three steek stitches and place them all on the hook.

DSC08312
Three steek stitches on yarn holder.
DSC08313
Hook placed through the three live stitches.
DSC08314
Yarnover the hook and pull through all 4 loops on the hook…

Then yarnover once more and pull all the way through. Cut your yarn.

DSC08315
Final steek reinforcement on one side.

You need to repeat this process on the other side – but you need to work in towards the center from the right. So you’ll start with the live stitches at the top.

DSC08316
Three live stitches at right top of steek.
DSC08317
Place slip knot on hook, and put hook through the three stitches.
DSC08318
Yarnover the hook and pull through all 4 loops on hook.

You will then be securing the left leg of the second stitch from the center and the right leg of the stitch to the right of center.

DSC08319
Insert hook in two legs to be secured…

Yarnover the hook and pull through all 3 loops on hook. Continue down the steek.

DSC08320
Hook inserted in next row.

Continue all the way down, ending by slip stitching over the cast on edge to secure it. Yarnover once more and pull all the way through. Cut your yarn.

DSC08324
Top of steek when finished.

You are now ready to cut!!

DSC08323details copy
Cutting line – you must be sure to NOT cut your crochet reinforcement.

Stay tuned for my steeking video – I should be posting it soon!

I’m blocking my sweater today, so hopefully I’ll be able to start the finishing in a day or two! I’m nearing the finish line….

6 thoughts on “Preparing to Steek”

  1. Hi Heather, Even though I don’t knit, the instructions were very easy to follow. You are really good at this. Thank you for all of us who have had a chance to read this.

  2. Heather, what great pictures. Looking forward to seeing your video. Your sweater looks beautiful; can’t wait to see it completely finished!
    Susan in Seattle (TKGA!)

  3. Thanks for such an informative post. I love all the pictures- makes it very easy to understand. I’ll be doing a crochet reinforcement on the baby blanket I’m making before I steek so I’ll definitely look to this post for guidance when doing so

    1. You’re very welcome! I do my crochet reinforcement a tiny bit differently than some other tutorials – I only do a slip stitch chain, but many others do a single crochet chain – either way works! The single crochet method is perhaps a tad bit even more secure, but I like the slip stitch since it’s less bulky.

Leave a Reply

This site uses Akismet to reduce spam. Learn how your comment data is processed.